Jump to content

Recommended Posts

I'm looking for some running boards for my NV 3500 passenger van.  This caught my attention because of how inexpensive it is: http://a.co/3wqXgZd

 

I'm looking for any opinions/advice to steer me in the right direction.  Are the cheap running boards worth trying?

 

Thank you!

Edited by Mark Rogers

Share this post


Link to post
Share on other sites

There are not a lot of choices out there which is weird since this van sees a lot of shuttle duty commercially.  I know a lot like the Luverne steps and we're looking at those to make it easier for my parents and in-laws to get in and out.  My kids just scramble in and jump out!  There are a few others but all are/were around the same price.  

 

One downside is the NV's require drilling.  All my past trucks had brackets that bolted right on no matter what brand you picked.  There were factory studs or threaded weld nuts that were installed to make it super easy.  The NV instructions for the Luverne's at least require drilling through the pinch weld and also into the rockers.  

Share this post


Link to post
Share on other sites

Those look identical to mine, there is no drilling g required, but I will say the very back of the passenger side needs another bracket added to what they send you.

Share this post


Link to post
Share on other sites

Those look identical to mine, there is no drilling g required, but I will say the very back of the passenger side needs another bracket added to what they send you.

 

Where did you get yours?  All the models I've seen require some sort of drilling which I'd like to avoid if possible.  Where did you get another bracket?

Share this post


Link to post
Share on other sites

Steelcraft stx600 from autoanything. I never added the rear bracket, only my kids step back there.

Share this post


Link to post
Share on other sites

Thanks, everyone.  I ordered the cheap ones and I'll give them a try.

Share this post


Link to post
Share on other sites

Liked the video and the recipes. Always looking for nutritious meals to talk traveling.

Share this post


Link to post
Share on other sites

That's a great video!

 

 

Liked the video and the recipes. Always looking for nutritious meals to talk traveling.

 

 

Thanks everyone!!

Share this post


Link to post
Share on other sites

I got the SteelCraft running boards.  I installed the passenger-side board last night and found that the rear bracket doesn't provide nearly enough support (Just like mk1_62 described earlier in this thread).  The brackets and board are very sturdy themselves, but the rear bracket only bolts to horizontal surfaces.  The other brackets bolt to both horizontal and vertical surfaces.  As a result, the sheet metal in the van's body flexes considerably whenever I step on the board near the rear bracket.

 

I sent a message to SteelCraft, asking if they have a solution.  I suspect it would require a redesigned rear bracket that may require drilling for installation.  I'd be fine with that, but I don't know where to get a better bracket.

Share this post


Link to post
Share on other sites

Mark, Keep us posted and send photos.  I'm still on the hunt. I did get a $653 quote from Radco for long/long arrangement, but I'm holding out on spending that much.  Did you find if TAC had a long/long option?

 

Larry

Share this post


Link to post
Share on other sites

Larry,

 

I didn't look for any long/long options.  Since people can only see one side of the van at a time, I don't really care if they match or not.   :)

 

Here's a photo of the passenger side running board from Steelcraft Automotive:

 

passenger side

 

I haven't installed the driver-side board yet.  I'm currently communicating with Steelcraft about the mounting issue.  The rear end of the passenger-side board sags about 1.5 inches when I step on it (distance between ground and running board, compared to when I'm standing on the step above the running board).  The van body is flexing, not the board or bracket.  I'm worried about causing metal fatigue in the body.  I'm hoping their R&D people will come up with a solution.

 

Mark

Share this post


Link to post
Share on other sites

After some discussion with Steelcraft Automotive, they agreed to send me a fifth bracket for the passenger side running board.  The red arrow shows where I mounted it:

 

5th bracket location

 
The bracket is identical to the #3 bracket. There's no hole in that location for the upper bolt. I considered drilling one, but it feels very secure with just the lower bolt, so I didn't bother.
 
The fifth bracket made a huge improvement in the strength and stability of the running board!  I'm really happy with the outcome.
Edited by Mark Rogers

Share this post


Link to post
Share on other sites

Mark, can you give me the name of the person you talked to? Brad at replaprints com

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...