Jump to content

Recommended Posts

Hello all,

 

 

Thought I would post a bit about my "new to me" van. I bought it with 8,000 miles on it. I live in Reno, Nevada and flew down to Kerney Messa to get it. Why fly to LA from Reno? The van had windows all the way around like a passenger van and that was a Must Have. I found it at Mossy Nissan. Great people by the way!

 

 

Anyhow, so I got up at 3am and I flew down there to get it.  I quickly completed the deal and left the dealership at high noon. However, the only draw down I saw was the 6 lanes of traffic for the next 3 hours. I think I saw the good the bad and the ugly of the freeways that day. I don't envy the commute anyone does down there...I used to live in the bay area and I thought it was bad there! I managed to get home at 10:30 that night. Decent time with 550 miles of travel and a few stops.

 

 

It's the cargo high top with the standard rubber mat in the back. The type with about an inch of sound proofing attached to the underside. It's the SV so it has Navigation (no subscription needed) thank goodness. The sound system has CD and Aux connection for MP3 players/phone. I use that with my S3 and it works great. The USB jack in the center console is great for charging. I also had to have the V8 I wanted a van that could get out of the way if needed. This thing is really quick for a cargo. I do notice that because it's huge (9ft high for those who don't know) it either intimidates people or upsets them into dodging around me and cutting me off to get around. I'm used to it now of course. I've been driving it around 2 months or so.

 

 

It's bare bones in the back with only simple panels in the back on the lower end. Below the windows and also the sliding door. I found that it was horribly loud while driving on the freeway. So on to the modifications.

 

 

I am just beginning so the list that is done is short. I decided on putting in Rattle Trap Extreme 80 mil. I have put this in on the sides of the van... in the side panels as far down as I could reach inside. It was really deep I'm not sure I quite made it down to the bottom. But it was pretty close. I also did the ceiling and panels above the windows....and of course the area above the cab. Even though it is trimmed out the rattle trap made a huge difference in road noise. I also put it in the rear doors and the sliding door. I did not do the floor because of the sound mat already in place. Just for your reference it took about 125-130 square feet of rattle trap. I paid roughly $300.00 for 150 square feet on ebay. I will probably be putting some of it on the sliding door step...currently removed..and I'll explain that shortly. I might also be putting it in the front doors as I have extra left over. When using the roller to avoid scratching the paint make sure you use the rounded edge towards the support bracing. If you are covering the roof/side panels it probably won't matter. Using actual sound proofing material seems to have been a great idea. There is almost Zero outgassing of the rattle trap. The smell is noticeable but not for long and it's made to stand up to the heat. Roof flashing material will sag or fall off during high heat. DON'T do it! Do it once and do it right! I used a 2x6 piece of wood with an outline of a 3 inch strip on it to cut multiple strips. I did about 10 strips at a time. Larger strips work well on the roof. But the sides and front cab areas needed smaller strips. (on the sides) Trying to install larger pieces in the side walls was horrible. Cut smaller strips it's much easier.

 

 

While driving back from LA it was up to 104 degrees. I could literally feel the heat cooking me from the rear of the van. So on top of the rattle trap extreme I also decided to install reflectix. This has made a huge difference in temperature. I don't have a temp gun to test it...sorry I can't report that. The reflectix was bought at home depot. It took about 1 and a half rolls to do the roof and cab roof areas. I believe it was 16 inches wide by 25ft long. To apply it I used 3m spray 90. It took almost 3 cans at $13.00 each. I used the same plastic roller supplied with the rattle trap to apply it. The reflectix when up much faster than the rattle trap. It was easy to cut several strips for the roof at a time then apply one at a time while while waiting for the 3m to tack up. I used a cardboard box laying on the concrete to apply the 3m to the installation piece. you spray 2 to 3 coats and wait until it tacks up. Using a knuckle of your finger to test. If the adhesive comes off on your knuckle...it's not ready to apply. Usually waiting 2 to 3 minutes for tacking time was enough for me.

 

So it was quickly apparent that "oops I have two kids" and two front seats won't do the trick. As of yet my entire family hasn't been in the truck driving yet. But this weekend we are installing the seats we bought. I purchased a 3 passenger bench seat from a 2015 Ford Transit. I spent $1,500.00 shipped to a local shipping dock. Not the best deal but for getting the job done properly it made sense and came with floor mounting rails. Most don't! So watch what you buy! These also have built-in shoulder seat belts. Which I did not want to half *ss in place. I've seen plenty of butcher jobs on youtube to know I didn't want to trust my children to an install like that. Some mental notes: First off the Ford Transit rails do NOT sit flat on the floor in the grooves your NV has. I had to place the rails on a piece of 2" flat bar metal to properly support them between the grooves. This allowed me to also put the mounting rails right where I needed them. You want to drill your holes through the support/cross beams not just straight through the floor anywhere... it isn't strong enough. Also use fender/large washers on top and bottom. I used grade 5, 1/2" bolts. 2 of them were 3-1/2" long  and 4 were 4" long. This is all for 2nd row directly behind the driver/passenger row. I also used lock washers on all of them. It's easy to see where the beams are by looking for the spot welds. You can go between them. I did all of this without dropping the muffler or the gas tank. Several of the bolts are where you cannot see them. One of mine ended up under a bracket for the parking brake lines. Pay attention to how many "walls" you drill through for that area. It should be two. If you run into three you are drilling into the bracket. I managed to catch the feeling of hitting another space while drilling. I removed the bracket and used a shorter bolt that fit right under the bracket. Also, make sure you don't drill into your gas tank or muffler! There is plenty of room if you only drill through the support brace. It's a two person job. Once drilled (on each one as you go) Someone needs to climb under the truck put the fender washer, lock washer, then the nut on. Most of this will be by feel since you can't see. Then use a wrench to hold the nut while the person on top uses a ratchet to tighten it. This makes it much easier than any other way I could come up with.

 

Well so far this is as much as I have done. I've began to cut the floor mat to allow for the brackets to stick through and I will post pictures of this wonderful thing maybe tomorrow. Sorry for the long post but I had to get it all out of my head!

 

Paul from Reno.

Share this post


Link to post
Share on other sites

Paul-

Welcome to the group and thank you for the post. It sounds like you are well on your way.

Don't hesitate to provide details - some may skim or skip as they read but others will absorb it all.

You might want to copy this post over to the conversions category and then just continue to add to the thread as you do more things to make the vehicle meet your needs.

Your concern for the safety of your family is noted and admirable. The first step you took towards that safety was buying the NV. Now you have a vehicle with excellent stability and comfort, a huge engine out front to help absorb impact should anything happen, and the largest and best set of brakes in the category. And yes, most other drivers seem to be a little bit intimidated by it - which doesn't hurt.

I'm looking forward to hearing about the fun you will have owning and modifying one of these unusual vehicles. Gotta question - just ask us - there's a great group here with a diverse set of skills.

Share this post


Link to post
Share on other sites

Welcome. Brought back memories of installing front and rear seat belts in our '62 Land Rover. Some 2 person jobs never change.

 

How do you plan to use your NV?

Share this post


Link to post
Share on other sites

Welcome!  Looking forward to photos and details of your build.

 

Mike

Share this post


Link to post
Share on other sites

Welcome. Brought back memories of installing front and rear seat belts in our '62 Land Rover. Some 2 person jobs never change.

 

How do you plan to use your NV?

I'll be hauling the odd pallet of cargo here and there. Of course I'll need to use the small trailer I have now to carry anymore than 1 since the seats are installed. I actually use it as my daily driver now. I originally had a dodge ram 2500 and had intended on going smaller. How'd I do? :) Also, during the winter I'll be driving it up to go skiing. So I'll be buying studded tires soon. Of course if its very rough I'll take the wife's car or get a ride from friends that ski as well. 

Share this post


Link to post
Share on other sites

So all in favor of me copying to conversions? I won't cause any trouble cross posting?(once)

Share this post


Link to post
Share on other sites

Smaller? Nissan commercial may be behind the curve or a full glass cargo/passenger NV200 isn't marketable, but they may have sold one to you.

 

I know the word is No towing for NV200s, but saw one the other day with a hitch. On our last trip, we saw all sorts of small vehicles pulling trailers. Add a hitch, attach safety chains and make sure the lights work seemed to be the norm.

 

Pallets? If you have a fork lift, I envision the first slide in camper or sauna build; yes, under conversions.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...