Caryn Williams

These are the biggest pics it will let me upload from my phone. I have the vented windows in the front sides. Evidently those are not the same size. Or that's what they told me at the dealer. This is all turned into a horrible nightmare. Don't buy your car from Cerritos Nissan. The general manager is super nice. But the sales people don't know squat.

Hi all I'm back, after fighting with the Nissan dealer for 2 months. I finally got the mid rear windows installed in my NV 1500. Now here's the problem they took it to some aftermarket place and returned it to me. With the inside of the windows without a frame all the cuts are Sharp and edges are ragged. Then it's bolted through and they left the bolts hanging out. It looks as if these have been cut off with bolt cutters. I have complain to the Nissan dealer so here's my problem. Nobody seems to know what to do to fix it. I use my van for dog walking and pet sitting. Right now it is unsafe to put animals in as for all the sharp points and edges in the back. On top of that the vehicles brand new and I'm horrified that they would return it to me in this condition. Really the problem is how do I fix it or how do I tell them to fix it. I have been looking for ways to find a frame for it. The stock windows for this are out on backorder and nobody knows when they will be in. So in the meantime I need to use my van for work. I live in Long Beach California so any ideas anyone. I could really use some help guys. I tried calling a van conversion place. They seemed very unhelpful and said they could help me maybe next week. The problem is I use this van everyday for work. So any ideas or help would be great. Other than reaming the Nissan dealer which I've already doing. I need to find a way to make it work in the meantime. Help

So today I put in the fuse but the console still has no power. I will look at it again in the morning. It looks from the new BBG guide that it goes in the number 9 slot under the hood. Please help if im wrong before I unbolt it. To see if the wire pulled loose when bolting in the console.

So today I put in the fuse but the console still has no power. I will look at it again in the morning. It looks from the new BBG guide that it goes in the number 9 slot under the hood. Please help if im wrong before I unbolt it. To see if the wire pulled loose when bolting in the console.

I gave up trying to remove the plastic backing. For now I just put a seat cover over it and remove the armrest. I am a dog walker I use my van for picking up dogs and transporting them from place to place. I was able to get the console in without removing the complete thing.

The console came with the 12 volt plug inside it and an existing wiring. Underneath the front passenger seat there is an existing plug for it. However to get to this plug. I had to remove the front seat or at least unbolt it to get clearance remove the rubber matting the plug is all the way up towards the front of the seat. Facing the opposite way. I was able to find pictures of the plug on this site. I then bolted in the center console. After returning the seat to its original position

Thank you thank you

Good morning,Jerry could you please tell me what slot it goes in? As I'm unable to find the info online?

Thank you, what a great idea I didnt even think of that.

Okay that's what mine looks like. Can you show me on there where the auxiliary fuse might go. Or Center console fuse? It's very sparse. I have looked at mine and tried to guess. I was hoping someone might know exactly.

Ok I've got the console. The 12volt charger inside is plugged in correctly. It doesn't work I believe its the fuse. My inside fuse box does not have the schematic for the console. So no idea where the fuse might go. Any ideas?

Okay I got the console in. I have it plugged in. But the charger in the console does not work. The fuse box in my NV does not have very much info on the back panel. If there's someone out there who has a center console. Could please take a picture of there fuse box lid other cab fuse box. It would be greatly appreciated. I've looked at several schematics. Having trouble figuring out which one it is. Any help out there that would be great.

Skip to main content eBay Enter your search keyword Search... Search Hi! Sign in My eBayExpand My eBay How to install the Center Console for the NV 1500 westcovinanissan westcovinanissan Like Share October 3, 2011 1. Remove head rest 2. Remove trim cover by pulling outward. Save trim cover for reuse. 3. Remove 12mm bolt from arm rest 4. Remove arm rest by pulling outward. 5. Unzip both zippers at back of seat cover. 6. Pull seat cover off right (inboard) side of seat back. 7. Locate armrest bracket, remove 8mm bolt and two 10mm nuts from arm rest bracket. Use care when moving seat foam away from seat frame to access armrest bracket. 8. Cut foam plug using template. Foam should be 2 ½ inches thick, high density and flame resistant. 9. Install foam plug into opening where armrest bracket was located. 10. Put seat cover back on seat and close both zippers. 11. Use a Sharpe marker to trace outline on foam plug through opening in seat cover where armrest was located. Mark an X where the center of the opening is located. 12. Unzip seat cover and move cover off the right side of the seat back; remove foam plug. 13. Center the shaft of the cover trim on the X marked on the foam plug. Using a Sharpe make an outline around d of the armrest trim cover shaft. 14. Using scissors cut out a hole in the foam plug along the outline. Leave approximately 8mm at the bottom of the hole. This will help secure the armrest trim cover. 15. Reinstall the foam plug into the seat back. 16. Place the armrest trim cover through the opening in seat back cover and secure it with the push nut (¾ pipe escutcheon). USE CARE to only push the nut (escutcheon) onto the shaft of the trim cover far enough so that the trim cover can be moved around in the seat fabric with some light resistance. Pressing the push nut / escutcheon too far will compress the fabric and may cause the fabric to pucker around the trim cover. CAUTION: The sharp edge of the push nut/escutcheon must face the seat foam NOT the seat fabric. 17. Place end of armrest trim cover into hole in foam plug. 18. Reinstall seat cover. The trim cover should be flat against the seat fabric and there should not be any puckers in the seat fabric around the trim plug. If there are puckers remove the seat cover and loosen the push nut, allowing the trim cover to move in the seat fabric with a slight amount of resistance. 19. Reinstall headrest. Pictures are coming soon... Tags: NCVNVcenterconsolenv1500 westcovinanissan westcovinanissan Welcome to the TheNismoShop aka West Covina Nissan! Here at TheNismoshop we will provide un-parallel customer service and wealth of knowledge in JDM & OEM parts which cannot be found in any other dealership worldwide!! Items for sale Additional site navigation About eBay Announcements Community Security Center Resolution Center Seller Information Center Policies Affiliates Help & Contact Site Map Copyright © 1995-2016 eBay Inc. All Rights Reserved. User Agreement, Privacy, Cookies and AdChoice Scroll to top

Fwd: http://www.ebay.com/gds/How-to-install-the-Center-Console-for-the-NV-1500-/m10000000084404370/g.htmlhere's a link to the instructions that I found

I need to remove the black plastic on the passenger seat. To get to where this seat bolts are that protrude for the armrest. Again the instructions say it just pulls off. Not so

Actually the post removed from the back of the seat. On the driver side which left a gaping hole. I believe I can put the plastic cover from the armrest. Into the hole somehow. But the eBay instructions say something about making a plug. And that's where it gets confusing.

I recently bought a NV 1500. It did not come with the center console so I ordered it separately. The console did not come with any directions. The only place I was able to find directions was on eBay. And they are very difficult to follow. I was able to get the console in. Both of the armrests removed. However I cannot get the plastic seat back off the passenger seat. I am unsure how to fill the hole where bolts were for the armrest. And I have no idea where to plug in the power for the charger in the console. I have not even attempted to bolt it down yet. Any help would be awesome. I'm pretty good at figuring things out. But this often takes longer. So any help would be great guys

I've got the arm rest's removed. From the driver's side seat. I'm unclear to the process for filling the holes. In the seats where the armrests bolts used to be. Also I'm not quite sure. Where the plug in the center console goes. Or how to remove the plastic backing off the passengers side seat back.

Im trying to install the stock center console in my 2016 NV 1500. Im looking for more clear directions. I did find some on eBay however they are a bit confusing. Any help would be awesome.